Interploy Irrigation, 62 Richmond Road, Kingston-Upon-Thames, Surrey, KT2 5EH.

0253 Spray Kit Ł29.00 Simple to install Ideal for Flowerbeds, Vegetable plots, Greenhouses, Ground cover and Polyfunnels. Will cover up to 65 ft. by 10ft of flowerbed.
0253D Double Spray Kit Ł39.00 Contains the same as the 0253 Spray Kit, plus an extra roll of 20m of 13mm polytube. 13mm joiner and 10 h/circle spray jets, allowing you to cover up to a 130ft length of flowerbed.

CONTENTS:
20Mts 13mm Polypipe	3/4 Tap Connector	3 13mm Tees	4 Elbows	3 Stop Ends	10 h/circle jets	10 f/circle jets	10 200 rigid risers	10 300 rigid risers	Punch

Suggested extras to add to your Spray Kit:
IN/MS/JS Jetstakes: used with 4mm polytube, where you want flexibility to place the spray jets away from the main 13mm supply line. Ideal for unusual shape or large flowerbeds.		RN12 Location Riser Pipestakes: will hold down 13mm of pipe and at the same time hold the rigid risers upright.

Installation instructions for a Spray Kit

1.Lay out 13mm (1/2") Polytube along the areas to be watered from the tap to the furthest point you wish to water. If you are using ˝" Tube the distance you can cover with the Spray Jets spaced at two metres apart will be approximately 40 metres in length on normal mains water pressure ie 25psi, once you get over 40 metres the pressure will start dropping when you use ˝"pipe. If you have a large garden you will have to divide your watering into separate zones. When you are laying the 13mm Tube it will help if you pour hot water on the pipe to take out the spring in it so that it lies flat. When you have finished laying it all out, before you fit your 13mm End plugs at the end of each line, screw the Tap connector on to the tap and turn on the tap to flush out any sediment from the 13mm tube.
2.You are now ready to locate your Spray jets. For the best results set the Sprays between one and a half to two metres apart. Simply pierce a hole with the Punch into the 13mm Tube and then self tap a Jet into the top of a threaded Rigid Riser and then screw the Riser with Jet into the hole. Where Spray Jets are used for overhead watering eg.Polytunnels, Shadehouses, attach the tubing to supporting beams, punch a hole in the13mm tube and self tap a Jet spray directly into the hole, or alternatively cut the riser to the desired height and screw a riser with Jet into the hole. Your Spray System is now ready to put into operation. Simply turn on your tap, each Spray Jet will apply water at a rate of approximately 60 litres per hour. If the Spray Jet begins to mist too much, the pressure is too high, reduce the pressure by turning down the Tap. If you put too many jets on the line the sprays will not give the required cover needed so you will have to reduce the amount on the line, the amount you can have depends on your water pressure.
EXTRA ITEMS YOU MIGHT ADD TO YOUR KIT
Location Riser Pipe Stake: it has two uses a)To hold the 13 mm Tube to the ground and b)To hold the Rigid Riser in a vertical position.
Microstake: this allows you to position your Spray Jets away from the main 13mm feeder Tube, attached to the Microstake is a 4mm Joiner Offtake and a 4mm Sealing plug which you break off to use. To use the 4mm Joiner simply pierce a hole in the 13mm Tube with the Punch, connect one end of the barb of the 4mm joiner to a length of 4mm Polytube, push the other end of the 4mm barb into the hole which you have made with the punch and then run the 4mm Polytube to where you wish to place the Microstake. If you wish to adjust the height of the Jet simply self tap the threaded end of a Rigid Riser into the 4mm Polytube and then self tap a Spray jet into the top of the Riser and then snap the Riser into the groove in the side of the Microstake, you will now be able to adjust the height of the spray by sliding the Riser up or down the Microstake.

Easy to Install Drip Kits

Go Top

0253 Drip Kit Ł39.00
Ideal for watering hanging baskets, pots, trees and shrubs

CONTENTS:
20M 13mm 20M 4mm Polypipe	10 4L/H Drippers	20 4mm Barbed Joiners	3 13mm Tees	4 Elbows	3 End Stops	3/4 Tap Connector	4 4mm Tees	10 v/flow drippers	10 Locking Clamps	Punch

Installation instructions for a Drip Kit

STEP 1
a) Screw the Tap Connector on to the Tap or Tap Timer and push on 13mm tube, in areas of high pressure use a Pressure Reducer Code 0090.
b) When operating the system turn the tap on slowly half a turn at a time until each Dripper has a constant flow rate.
c) If the water has impurities install an Inline Filter and secure with 13mm Locking Clamps.
d) Using Variable Flow Drippers the flow can be adjusted by rotating the Dripper head. Fixed Flow Drippers provide a set amount of water per hour.

STEP 2
Lay 13mm Tube alongside your Pots, Hanging baskets, Shrubs or Trees, decide where you will need 13mm Tees, Elbows, and End Plugs. Cut 13mm Tube with Scissors, insert the correct fitting and secure with a 13mm Locking Clamp if required. To connect the 4mm Tube to the 13mm Tube, using the Punch, make a hole in the 13mm Polytube and push the 4mm Barbed Joiner with it connected to the 4mm Polytube into the hole made by the Punch, when you push the 4mm Joiner into the 13mm Tube make sure that it has clicked firmly in the Hole, run the 4mm Tube where you want to place a Dripper, cut the 4mm Tube and push it onto the Barb on the Dripper. Place the Drippers about 5cm away from the base of each plant. Finally push on a 13mm End Plug secured with a 13mm Locking Clamp at the end of each branch of the 13mm Tube.

Easy to Install Aqua Shuttle Kits

Go Top

Aqua Shuttle Kit
A comprehensive kit which allows you to mist, spray or drip watering.

Ł13.00

CONTENTS:
Aqua Shuttle with tap adapter RN070005 Price Ł6.00	12 meters of 4mm Polypipe	6 x variable flow drippers on stakes
FEATURES AND BENEFITS:
The Aqua Shuttle has been designed as a multi-purpose watering product for use in small gardens, on verandahs, porches, balcanies, pergola's and in hot houses. The Aqua-Shuttle is a powerful and versitile watering distributor, which enables you to water specific plants or clusters of plants. The Aqua-Shuttle is compatible for use with drippers, jet-sprays, misters, micro-sprinklers and/or any of our micro sprays and jets. The Aqua-Shuttle is fully adjustable for controlling the amount of water provided to the designated plants, by the adjustable taps. These can be adjusted to either control the watering to individual plants or be turned 'off' for those plants that do not require watering every day. Winner of the award for the 'Most Innovative New Product' at the 1998 Nationa Japan DIY Show.
TO EXTEND YOUR KIT:
Aqua Shuttle RN070012 Price Ł5.40	Back to Back Nut RN71477 Price Ł1.40
Used to distribute water via 4mm riser tube to a cluster of plants. 3/4" BSP male thread inlet and six 4mm barb outlets, each controlled with their own value to adjust the water to each line. The Aqua Shuttle provides total control and flexibility. Use any combination of drippers and sprays and adjust the watering for all plants. Back to Back Nut. This connects two Aqua-Shuttles together for additional watering applications, or used to adapt Aqua Shuttle to 3/4" tap outlets.
INSTALLATION TIPS:
If the flexi tube is "blowing off" the barbs you may have high pressure in your area. If this is happening, use the taps at the Aqua-Shuttle to regulate the flow in the system. Flush your Aqua-Shuttle regularily. Make sure all taps are "off" and then remove then end cap. Turn on the tap and allow the water to flush the Aqua-Shulttle. The Back to Back nut allows you to extend your Aqua Shuttle watering system with ease. Although the Aqua Shuttle system comes complete with adjustable drippers on stakes, you can customise your watering system be selecting from different kinds of Drippers, Sprays and Sprinklers.

Easy to Install Greenhouse Kits

Go Top

0251 Greenhouse Kit
A comprehensive kit which allows you to mist, spray or drip watering in the greenhouse.

Ł35.00

CONTENTS:
20M 13mm 5M 4mm Polypipe	10 4v/flow Drippers	20 4mm Barbed Joiners	3 13mm Tees	4 Elbows	3 End Stops	3/4 Tap Connector	5 h/circle jets	5 Mist Sprays	4 Qtr circle sprays